Bonjour à tous,

une question déjà dans le titre, je vais recevoir sous peu ma neuf box (fast 3302) ma question :
pourrais y brancher mon routeur externe? et desactivé le mode routeur du fast 3302? j'ai posé la question au service technique qui m'ont dit oui mais je voudrais l'avis de personne qui s'y connaisse!!!

merci à vous

Tu ne peux pas désactiver la fonction routeur de la F@st3302.

Cela n'empêche pas de mettre un autre routeur derrière.

merci de m'avoir répondu jeumeu

@++

JE ne suis pas tout a fait d'accord, suite a un topic existant , que je joins ci apres,


Bonjour,
Pardon not being able to respond en Francais.

I have the 3202 sagem neufbox, and I have SUCCESSFULLY been using it in "bridge mode" with a netgear 4-port MR814v2 router.

In this method, the netgear Router is supplying the login and password for my adsl account, and is also supplying my network with DHCP.

Instructions:

1. Connect the 3202 sagem modem directly to your PC, and use http://192.168.30.1/ to connect to the 3202's webpage interface.

2. In the "Basique/Maintenance" section, Click "Retablir la configuration initiale". This is especially important if you have made any changes to the configuration of the modem, including login/pw. Your modem with then RESET.

3. Then go to the section "Avance/DHCP". Click on the Selection button, and Click "Arreter".

Then Click "Maintenant".
Then Click "Supprimer"
Then Click "Sauvegarder".

In the menu on the left, go to "Tableau de bord".
You will see that Serveur DHCP is "Desactive".

4. Now, go back to "Avance/DHCP". You may find that the entry for DHCP is still there! Repeat this procedure again:

Click on the Selection button,
and Then Click "Supprimer"
Then Click "Sauvegarder".

Now in the "DHCP" panel, it should say "Aucun serveur DHCP disponible".

Now you have made the 3202 completely disactivate DHCP, so that your secondary ROUTEUR can supply your network DHCP.

5. Firewall/(Pare Feu): You may want to completely disactivate the firewall in the 3202, so that you can use a software firewall solution, or your secondary ROUTERS firewall configuration. To do that, go:

Firewall

you will see 2 lines of "Interface de reception" installed. Click on each individually, and click "supprimer". Both will disappear.

Make sure that "interface de reception" and Interface d'emission" are both set to "Acune"

Now the 3202's firewall will be disactivated COMPLETELY and not block any ports.

NOW you can close the WebBrowser window, and re-connect your 3202 ethernet cable directly to your Secondary Router's internet port, and your PC and/or other computers ethernet cables, directly to the ports on the Secondary Router.

The configuration is now complete, and you should have internet access supplied by the 3202 in "BRIDGE MODE", with your Secondary Router supplying DHCP and your NEUF Login and Password (from your Secondary Routers configuration page, usually accessable thru http://192.168.0.1/ )

------------------------------------------------------------

IMPORTANT NOTE:

If you decide at a LATER TIME to reconnect your pc DIRECTLY to the 3202 router in order to access the web browser interface, you will COMPLETELY LOSE the configuration above and the 3202 will RESET itself back to DHCP MODE control. Of course, its reparable by doing the steps above.

Why would you want to connect your PC directly to the 3202?

Because once you are in "BRIDGE MODE" as stated above, you will NOT be able to access the 3202's configuration page using http://192.168.30.1/ - it seems its only possible when the PC is connected directly to the 3202.

Thats it. Bon Courage and I hope this helps you all.

Do send email feedback and let me know if this worked for you, or respond in the thread.


=========> Bon courage pour tester.. et REvalider la procedure...

Le topic cité est assez ancien, et surtout il date d'avant la dernière mise à jour du firmware.

De toute façon, tu peux cascader des routeurs.